Durkota

Mr.gutsy · Post by **Mr.gutsy** » Mon Mar 02, 2020 8:03 pm

pointsnorth wrote: ↑Mon Mar 02, 2020 6:19 pm Picture of the inline cap?

Sent from my iPhone using Tapatalk

Got a moroso unit il take a pic tomorrow

HillBilt · Post by **HillBilt** » Tue Mar 03, 2020 9:08 am

Love the hood

Mr.gutsy · Post by **Mr.gutsy** » Tue Mar 03, 2020 3:09 pm

Forgot to snapa pic of the filler cap but what are ypu guys doing for securing brakelines to your links? Mine are just ziptied for now

HMF · Post by **HMF** » Tue Mar 03, 2020 8:05 pm

I know a guy that can get you bullet aluminum clamps for that stuff... can also incorporate the hydraulic lines into them too...

Post by **pointsnorth** » Wed Mar 04, 2020 8:12 am

I use these

Hmf burned them out on his table for me

Tmr also makes them but their about half the size
Sent from my iPhone using Tapatalk

Post by **Scott Cee AKA 2drx4** » Wed Mar 04, 2020 9:51 am

Mr.gutsy wrote: ↑Tue Mar 03, 2020 3:09 pm Forgot to snapa pic of the filler cap but what are ypu guys doing for securing brakelines to your links? Mine are just ziptied for now
20200303_124158.jpg
20200303_145916.jpg

I normally weld a bolt on to make a stud and then use P-clamps. Never done it on a link bit I'd probably do the same thing... a clamp you could re-index if you adjust the link might be better though.

Snowracer · Post by **Snowracer** » Wed Mar 04, 2020 10:19 am

Russell makes fittings and brackets to hold the lines, then run a hose clamp around the link. thats what i have done

HillBilt · Post by **HillBilt** » Wed Mar 04, 2020 10:36 am

I also used pico clamps along the diffs. Hose clamps along the links, haven't had an issue yet.

WelfareDuty · Post by **WelfareDuty** » Wed Mar 04, 2020 5:55 pm

Mr.gutsy wrote: ↑Tue Mar 03, 2020 3:09 pm Forgot to snapa pic of the filler cap but what are ypu guys doing for securing brakelines to your links? Mine are just ziptied for now
20200303_124158.jpg
20200303_145916.jpg

Like Erik said Russel makes little brackets then hose clamp them to the link

Mr.gutsy · Post by **Mr.gutsy** » Thu Mar 05, 2020 6:15 pm

For timber here is the inline filler the vent nipple is on the other side

Mr.gutsy · Post by **Mr.gutsy** » Sat Mar 07, 2020 10:58 pm

Im pretty sure I have room to get the rad out

Post by **Scott Cee AKA 2drx4** » Sun Mar 08, 2020 7:25 am

That's a good thing.

HillBilt · Post by **HillBilt** » Mon Mar 09, 2020 10:01 am

Front end is coming together nicely

Mr.gutsy · Post by **Mr.gutsy** » Sat Mar 14, 2020 10:07 pm

Not sure how but my tube is way out to lunch i must have been drunk when i put it on. Anyways putting the front bumper together its 3/8" t1 i made a jig and did a triple pass on it.

Post by **pointsnorth** » Sun Mar 15, 2020 7:03 am

Mr.gutsy wrote:Not sure how but my tube is way out to lunch i must have been drunk when i put it on.

Lol I’m not the only one

Sent from my iPhone using Tapatalk

4x4 North

Durkota

Re: Durkota

Re: Durkota

Re: Durkota

Re: Durkota

Durkota

Re: Durkota

Re: Durkota

Re: Durkota

Re: Durkota

Re: Durkota

Re: Durkota

Re: Durkota

Re: Durkota

Re: Durkota

Re: Durkota